Clone mac mini hard drive

To clone a hard drive, you will need a way to connect the second hard drive to your Mac.

Our silicone 2. To clone your hard drive, we recommend a program called SuperDuper!

• Simple clone method of cloning your hard drive to a new SSD.
• mbox mail for mac setup!
• Introduction.

If you are using a different setup, your installation process may be somewhat different. Buy these parts. You will need to put the new drive into the 2. Before inserting the new hard drive, note the orientation of the SATA connectors embedded in the enclosure:. Using the previous step, orient the new drive so that its SATA connectors will align with the enclosure's. Push the drive into the enclosure until it stops sliding and the SATA connectors are completely seated. Stretch the remaining enclosure corners over the drive so that the silicone cover encapsulates the drive.

If the new drive is not showing up, disconnect the enclosure and check if the hard drive is properly connected to the enclosure. Pressing the erase button will erase the entire contents of the drive. Make sure you have selected the new hard drive! Download and install SuperDuper! Under the Go pulldown menu, select Applications.

In the method pulldown menu, select "Backup—all files". Wait for the drive to copy this could take several hours if you have a lot on your hard drive. When prompted for registration by SuperDuper! After the copy is complete, click "Ok" and quit SuperDuper! At this point, your new hard drive should be a clone of your existing drive and ready to install.

However, we recommend testing the cloned drive before physically swapping the drives. This can be done by attempting to boot from the new cloned drive through the USB enclosure. Keep the enclosure connected to the computer and restart the computer. Hold down the "option" key as it reboots until a boot option menu shows up.

Part 1: Prepare

Remove your new hard drive from the external enclosure and install it in your computer. Installation instructions are available for a variety of Macs. I did not complete this guide. This guide was straightforward and helpful along the way when I replaced my hard drive! My only comment is that this should be a link in the "MacBook Pro 13" Unibody Early Hard Drive Replacement" article, since the Youtube videos link to each other, but the articles do not.

Thanks for all your help with these fantastic guides! Great except you extol the use of the SATA Wondercable but you don't sell it hen I followed the link to eBay, it listed dozens of various adapters. Everything went very well with a big bonus. My older version of Photoshop does not work with the newer Mac operating systems. You will have to use something like Winclone to do that.

Select a Language: Help Translate iFixit. Clone an Existing Drive Written By: Using a block copy is faster, but it does have some limits that affect when it can be used, the most important being that copying block by block requires that both the source and destination devices be first unmounted from your Mac. This ensures that block data doesn't change during the copy process.

But it does mean that neither the source nor the destination can be in use when you use the Restore capabilities.

If you need to clone your startup drive, you can make use of either your Mac's Recovery HD volume or any drive that has a bootable copy of OS X installed. We'll provide information about how to use the Recovery HD Volume to clone your startup drive, but first, we'll look at the steps in cloning a non-startup drive attached to your Mac. The Disk Utility app will open, displaying a single window divided into three spaces: If the Disk Utility app looks different then this description you may be using an older version of the Mac OS.

You can find instructions cloning a drive using an earlier version of Disk Utility in the guide: The volume you select will be the destination drive for the Restore operation.

A sheet will drop down, asking you to select from a drop-down menu the source device to use for the Restore process. The sheet will also warn you that the volume you selected as the destination will be erased, and its data will be replaced with data from the source volume. Use the drop-down menu next to the "Restore from" text to select a source volume, and then click the Restore button. The Restore process will begin.

A new drop-down sheet will display a status bar indicating how far along in the Restore process you are. You can also see detailed information by clicking the Show Details disclosure triangle.

Apple Footer

Click Done to close the Restore sheet. When you use the Restore function, both the destination and the source must be able to be unmounted. Instead, you can start your Mac from another volume that contains a bootable version of the Mac OS.